Efficiency testing on ships

On ships, as little visible smoke should be produced as possible, and the soot content kept to a minimum. A high soot content on deck can lead to the danger of soot deposits on the passengers. In order to test whether the smoke count of marine diesel engines does not exceed the prescribed limit values, shipping companies (and port authorities) can use a smoke tester. Use of the instrument provides clarity regarding the smoke values. In shipbuilding, the smoke count also plays an important part. After individual components have been assembled (engine, diesel particle filter, exhaust pipe), the soot emissions should be tested. In addition to this, for environmental reasons the customers often make demands regarding the emission values, and require proof of the soot emission in the diesel exhaust. The correct functioning of the diesel particle filter can also be testing using a degree of blackening measurement.

13 products or recommendations for Efficiency testing on ships
  • Modular flue gas probe, 335 mm, Ø 8 mm, Tmax 1000 °C

    Order-Nr. 0600 8764

    The modular flue gas probe with 335 mm long probe shaft including integrated thermocouple up to 1000 °C and quick-change click system (for quick replacement of the probe shaft).
    • Easy probe shaft replacement via quick-change click system

    • NO2/SO2 special hose (length: 2.2 m)

    • Flue gas path and temperature channel can be connected to the instrument via a bayonet lock

    • Integrated thermocouple probe for temperature measurements up to 1000 °C

  • Industrial probe kit 1200°C

    Order-Nr. 0600 7610

    Ideal for the extractive sampling of flue gas at high flue gas temperatures. The industrial probe kit 1200°C comprises a handle, a probe shaft up to 1200°C flue gas temperature, a 4 m long gas sampling hose, including inline filter (all three unheated) and a thermocouple type K.
    • Can be used in combination with testo 340 and testo 350

    • Additional inline filter to protect the gas sampling hose from contamination

    • Unheated sampling tube (1 200 °C) can be extended up to max. 3 m using optional extension tubes

    • Very easy to handle

  • Modular flue gas probe, 335 mm, Ø 8 mm, Tmax 500 °C

    Order-Nr. 0600 9766

    The modular flue gas probe with 335 mm long probe shaft including integrated thermocouple up to 500 °C and quick-change click system (for quick replacement of the probe shaft).
    • Easy probe shaft replacement via quick-change click system

    • NO2/SO2 special hose (length: 2.2 m)

    • Flue gas path and temperature channel can be connected to the instrument via a bayonet lock

    • Integrated thermocouple probe for temperature measurements up to 500 °C

  • Modular flue gas probe, 700 mm, Ø 8 mm, Tmax 500 °C

    Order-Nr. 0600 9767

    The modular flue gas probe with 700 mm long probe shaft including integrated thermocouple up to 500 °C and quick-change click system (for quick replacement of the probe shaft).
    • Easy probe shaft replacement via quick-change click system

    • NO2/SO2 special hose (length: 2.2 m)

    • Flue gas path and temperature channel can be connected to the instrument via a bayonet lock

    • Integrated thermocouple probe for temperature measurements up to 500 °C

  • Modular flue gas probe 700 mm, Ø 8 mm, Tmax 1000 °C

    Order-Nr. 0600 8765

    The modular flue gas probe with 700 mm long probe shaft including integrated thermocouple up to 1000 °C and quick-change click system (for quick replacement of the probe shaft).
    • Easy probe shaft replacement via quick-change click system

    • NO2/SO2 special hose (length: 2.2 m)

    • Flue gas path and temperature channel can be connected to the instrument via a bayonet lock

    • Integrated thermocouple probe for temperature measurements up to 1000 °C

  • Modular flue gas probe with pre-filter, Ø 14 mm, 700 mm, Tmax 1000°C

    Order-Nr. 0600 8767

    The modular flue gas probe with preliminary filter Ø 14 mm, 700 mm long probe shaft, thermocouple up to 1000 °C and quick-change click system (for quick probe shaft replacement).
    • Easy probe shaft replacement via quick-change click system

    • Preliminary filter offers protection from dusty flue gases

    • Flue gas path and temperature channel can be connected to the instrument via a bayonet lock

    • Integrated thermocouple probe for temperature measurements up to 1000 °C

  • Flue gas probe for industrial engines

    Order-Nr. 0600 7555

    The flue gas probe from Testo can be used to carry out efficient and reliable flue gas measurements on stationary industrial engines. It can be used at flue gas temperatures of up to 1,000 °C.
    • Additional particle filter in the hose provides protection from contamination

    • Probe shaft is easy to replace

    • Made of metal: no melting of the handle due to radiated heat from the flue gas duct

    • Temperature measurement possible with optional thermocouple

  • Stainless steel Pitot tube, length 750 mm - for measuring flow velocity, including temperature measurement

    Order-Nr. 0635 2042

    Robust Pitot tube for measuring flow velocity: the Pitot tube provides the optimum conditions, especially for higher flow velocities and for heavily contaminated flow. The 750 mm long Pitot tube has integrated temperature measurement and a connection hose with a maximum load capacity of up to 700 hPa (mbar).
    • For measuring flow velocity

    • Ideal for high flow velocities and heavily contaminated flow

  • Modular flue gas probe with pre-filter, 335 mm, Ø 14 mm, Tmax 1000°C

    Order-Nr. 0600 8766

    The modular flue gas probe with preliminary filter Ø 14 mm, 335 mm long probe shaft, thermocouple up to 1000 °C and quick-change click system (for quick probe shaft replacement).
    • Easy probe shaft replacement via quick-change click system

    • Preliminary filter offers protection from dusty flue gases

    • Flue gas path and temperature channel can be connected to the instrument via a bayonet lock

    • Integrated thermocouple probe for temperature measurements up to 1000 °C

  • Thermocouple for engine probe

    Order-Nr. 0600 8898

    You can use the thermocouple to measure the flue gas temperature in parallel with flue gas measurement on industrial engines
    • Temperature measurement in parallel with the flue gas measurement on industrial engines

    • Thermocouple with fast response time

    • Can be installed on-site by the user

    • Heat protection handle for comfortable handling even at high temperatures

  • Heated industrial probe set

    Order-Nr. 0600 7630

    Ideal for official emission measurement (compliance testing): the heated industrial probe kit comprises a heated probe shaft up to 600°C flue gas temperature, a heated gas sampling hose (length 4 m) and a thermocouple type K – this means you are ideally equipped.
    • Measurements in applications with flue gas temperatures of up to 600 °C

    • Short time needed to set up the heated industrial probe (ready for operation in 20 minutes maximum)

    • A high degree of measuring accuracy, even if the flue gas contains high concentrations of NO2 or SO2

    • Very easy to handle

  • Flue gas probe with preliminary filter for industrial engines

    Order-Nr. 0600 7556

    The flue gas probe from Testo makes it possible to carry out efficient flue gas measurements on industrial engines. In the case of diesel engines, the permanently welded-on preliminary filter provides protection from diesel particulates. It can be used at flue gas temperatures of up to 1,000 °C.
    • Additional particle filter in the hose provides protection from contamination

    • Useful for measurements on diesel engines: preliminary filter provides protection from diesel particulates

    • Made of metal: no melting of the handle due to radiated heat from the flue gas duct

    • Temperature measurement possible with optional thermocouple

  • Industrial probe kit 1800°C

    Order-Nr. 0600 7620

    Ideal for the extractive sampling of flue gas at high flue gas temperatures, e.g. in glass and steel production. The industrial probe kit 1800°C comprises a handle, a probe shaft up to 1800°C flue gas temperature and a 4 m long gas sampling hose, including inline filter (all three unheated).
    • Additional inline filter protects the gas sampling hose from contamination

    • Measurements in applications involving high flue gas temperatures of up to 1 800 °C

    • Very easy to handle

13 Products found