testo 312-3 - Instrument de măsurare a presiunii, de până la 300/6000 hPa

Cod produs  0632 0314

  • Măsurarea rapidă a scurgerilor de gaze

  • Testarea etanșietății conductelor de gaz

  • Domeniu de măsurare interschimbabil, rezoluție optimă

  • Funcţia de alarmare - când limitele definite de către utilizator sunt depăşite

Tot ce aveți nevoie pentru a inspecta instalațiile de gaz: cu instrumentul electronic de măsurare a presiunii testo 312-3 se poate testa etanșeitatea sistemelor.

1.928,00 RON
2.294,32 RON incl. TVA

Descriere produs

Testo 312-3, manometru versatil pentru pre-testarea şi testarea conductelor de apă sau gaz de până la 6 bar. Schimbările de presiune cauzate de schimbările temperaturii în timpul măsurării sunt echilibrate cu funcţia de compensare a temperaturii.


Conținut pachet

Instrumentul de măsurare a presiunii testo 312-3, incluzând bateria și protocolul de calibrare. 
Măsurarea presiunii


-300 … 300 hPa

-6000 … 6000 hPa

1 hPa (-6000 … +6000 hPa)

0,1 hPa (-300 … +300 hPa)


±0,5 hPa (0 … +50,0 hPa)

±1,5 % din valoarea măsurată (> 50 hPa)

±4 hPa (0 … +400 hPa)

±2 % din valoarea măsurată (+400 … +2000 hPa)

±4 % din valoarea măsurată (+2000 … +6000 hPa)

Rel suprasarcină. (presiune joasă)

±8000 hPa

Date tehnice generale


215 x 68 x 47 mm

Temperatura de operare

+5 … +45 °C



Semnal alarmă

Auditiv; optic

Limită inferioară alarmă

-0.04 hPa

Limită superioară alarmă

100 hPa

Tip baterie

baterie 9V

Tip afișaj


Dimensiune afișaj

2 linii

Temperatura de depozitare

-20 … +60 °C


300 g

Accesorii adiționale și piese de schimb

Acumulator de 9V pentru instrument

Cod produs: 0515 0025

61,00 RON
72,59 RON incl. TVA
Incărcător acumulator 9V

Cod produs: 0554 0025

56,00 RON
66,64 RON incl. TVA


Transport și protecție

148,00 RON
176,12 RON incl. TVA

Pressure measurements on burners

Checking the gas pressure on burners is one of the standard measurements during services of domestic heating systems. This involves measuring the gas flow pressure and gas resting pressure of the system. The flow pressure, also called supplied pressure, refers to the gas pressure of the flowing gas and resting pressure of the static gas. If the flow pressure for gas boilers is slightly outside the 18 to 25 mbar range, adjustments must not be made and the appliance must not be put into operation. If the burner is nevertheless put into operation, it will not be able to function properly and, when the flame is generated, small explosions will occur and ultimately malfunctions; the burner will therefore shut down and the heating system will fail.

Pressure tests on water pipes

According to the legal regulations of DIN EN 806-4, DIN 1988-7 and DIN 1610, drinking and waste water pipes are to be tested for leaks before being put into service by means of a pressure test with air, inert gas or water; they are also to undergo load testing with air or inert gas. However, for reasons of hygiene, it is best if the pipes remain dry until shortly before commissioning and do not undergo a leak test using water. A pressure test with air is also recommended to prevent metallic materials from corroding. The pressure test is split into two pressure-related parts where test pressure and time depend on the objective (load or leak). Leaks can usually be heard very quickly. If it is difficult to locate the leaks, the usual auxiliary tools and materials for gas pipes are used (spraying or brushing on foaming solutions).

Pressure tests on gas pipes (leak, load test)

The technical regulation for gas installations (in short: TRGI) is a binding and at the same time important regulation for skilled tradespeople. The TRGI governs how gas installations are to be planned, designed, serviced and maintained. This applies to all gas installations. This regulation is taken care of by the German Association for Gas and Water (DVGW). The TRGI 2008 is the current version. Amongst other things, this states that gas pipes are to be tested according to the construction phase (basic shell, completion and repairs). The following checks in particular play a role in the application stated here:

Load test
In this process, the material is tested for stability and the connections for service life; this takes place prior to plastering over or concealment of the gas pipes. During load testing, the newly installed pipe, without fittings or gas appliances, is subjected to 1 bar pressure. The testing medium is air or inert gas. There must be no pressure drop detected during the test, which lasts at least 10 minutes.

Leak test
This test is for checking the pipe for leaks, with fittings and without gas appliances. The measuring instrument must not register any drop in pressure during the minimum 10-minute testing period (depending on the system volume); the test pressure is 150 mbar (previously 110 mbar).

Temperature measurements on radiators

When measuring temperatures on radiators, the flow and return temperature are recorded in particular and assessed by the tradespeople. The flow temperature is defined as the temperature of the thermal transfer medium (e.g. water) that the system is supplied with. The temperature of the medium flowing out of the system is correspondingly called the return temperature. To prevent losses within the heat distribution system and achieve a better level of efficiency, spot recording of flow and return temperatures is necessary. Implementation of relevant measures ultimately leads to hydraulic adjustment on the basis of knowledge about the flow and return temperatures. This defines a procedure with which every radiator or heating circuit of a flat radiator within a heating system is supplied at a set flow temperature with the precise amount of heat needed to achieve the ambient temperature required for the individual rooms. Flawed operating conditions will result in considerable excess consumption of electricity and heating energy. The German Energy Saving Regulation (EnEV) requires hydraulic adjustment for systems being set up or overhauled for this very reason.