testo 380 - Particulate matter measurement system

Sipariş no.  0632 3801

  • The system comprises testo 380 particulate matter measuring instrument and testo 330-2 LL flue gas analyzer

  • Complete solution for solid fuel, oil and gas systems 

  • Fully TÜV-tested for limit value levels 1/2 and according to VDI 4206 Sheet 2

  • Particulate matter measurement, simultaneous O2 and CO measurement

With the testo 380 particulate matter measurement system, you can carry out uncomplicated particulate matter measurements directly on site. The completely new method of measurement developed by Testo enables the particulate matter to be monitored and limit values to be enforced. The measurement system is your professional tool for solid fuel, oil and gas systems.

Ürün bilgisi

The constantly rising number of solid fuel systems is leading to a further increase in the emission of particulate matter. The revised version of the 1st German Federal Immission Control Ordinance (BImSchV) presents new challenges for flue gas inspectors, heating engineers and service engineers when it comes to particulate matter measurement.

testo 380 particulate matter measurement system – complete solution for solid fuel, oil and gas systems

The testo 380 particulate matter measurement system comprises two system components: the testo 380 particulate matter measuring instrument including particulate matter probe and the testo 330-2 LL as a control centre and flue gas analyzer. This complete system is extremely compact, easy to use and ensures accurate measurements on solid fuel, oil and gas systems.

Advantages of the testo 380 particulate matter measurement system for particulate matter measurement

  • Suitability permit received for fuels 1-8, levels 1 and 2
  • Measurement system comprising testo 380 particulate matter measuring instrument and testo 330 LL flue gas analyzer
  • The testo 380 particulate matter measuring instrument allows you to carry out effortless and straightforward measurements directly on site
  • testo 330 LL flue gas analyzer: System control centre and flue gas analyzer
  • Parallel measurement of particle matter, O2 and CO in real time
  • Charts used to show all required measuring values for an optimum overview
  • Particularly cost-effective operation and maintenance
  • Effortless handling and easy transportation
  • Fully TÜV-tested for limit value levels 1 and 2 and according to VDI 4206 Sheet 2
  • High-tech in a portable case: measurement of all relevant values with just one probe

 

Teslimat kapsamı

testo 380 particulate matter measurement system incl. testo 380 particulate matter measuring instrument with particulate matter probe and cleaning set, testo 330-2 LL flue gas analyzer with mains unit (incl. Bluetooth, H2-compensated CO cell), modular flue gas probe (length 300 mm, Ø 8 mm), combustion air temperature probe (length 190 mm).

 
Genel teknik bilgiler

Ölçüm aralığı

0 … 300 mg/m³

Doğruluk

acc. VDI 4206-2

Çözünürlük

0,1 mg/m³ (>5mg/m³)

Boyutlar

475 x 360 x 190 mm

Çalışma sıcaklığı

+5 … +40 °C

Gövde

ABS

Koruma sınıfı

IP40

Ekran tipi

LCD

Ekran fonksiyonu

shows warm-up phase and operational readiness

Güç kaynağı

via internal mains unit: 100 V AC/0.45 A to 240 V AC/0.2 A (50 to 60 Hz)

Maksimum

500.000 readings

Depolama sıcaklığı

-20 … +50 °C

Ağırlık

7900 g

Whether flue gas inspector/chimney sweep, service engineer or heating engineer: testo 380 is the ideal aid.

If particulate matter measurement has never presented any difficulty - it won't take long to learn how this works: the particulate matter measurement system will guide you through the measurement, analyse the relevant particulate matter, O2 and CO values in parallel, and illustrate these in a diagram. Regardless of whether you are carrying out an acceptance test, or would like to set a combustion system to best effect: with the particulate matter analyzer testo 380, the new challenges of particulate matter measurement can be faced with confidence.

Thanks to testo 380, the legal guidelines and regulations regarding the acceptance testing process are easily met: the acceptance test integrated into the measurement menu follows the official process set out by the first German Emission Control Ordinance (BImSchV). The intuitive menu guidance ensures that none of the stipulated steps are missed out: core flow and draught measurement are already integrated into the measurement process; important work stages are constantly prompted.

Your challenging task as a service engineer and tradesman in the areas of heating and sanitary facilities is to set solid fuel systems on site to perform efficiently and meet the new limit values. The measurement program “setting assistant” is an excellent aid: it allows you to carry out measurement procedures with ease; in fact, the testo 380 can perform several measuring cycles in a row without any difficulty.

Ürün broşürleri

Yazılım