Image
  1. Home
  2. testo 380
0632 3801

testo 380 - Fine particle measuring system

testo 380 Feinstaub-Messsystem
testo 380 - Feinstaub-Sonde
testo 380
testo 380
With the testo 380 fine particle measuring system, you can carry out uncomplicated particulate matter measurements directly on site. The completely new method of measurement developed by Testo enables particulate matter to be monitored and limit values to be enforced. The measurement system is your professional tool for solid fuel, oil, and gas systems.
  • The system comprises testo 380 particulate matter measuring instrument and testo 330-2 LL flue gas analyzer
  • Complete solution for solid fuel, oil and gas systems 
  • Fully TÜV-tested for limit value levels 1/2 and according to VDI 4206 Sheet 2
  • Particulate matter measurement, simultaneous O2 and CO measurement
The constantly rising number of solid fuel systems is leading to an increase in the emission of particulate matter. The revised version of the 1st German Federal Emission Control Ordinance (BImSchV) presents new challenges for flue gas inspectors, heating engineers, and service engineers, when it comes to particulate matter measurement.

testo 380 fine particle measuring system – complete solution for solid fuel, oil, and gas systems

The testo 380 fine particle measuring system is comprised of two system components, the testo 380 fine particle measuring instrument, including particulate matter probe, and the testo 330-2G LL as a control center and combustion analyzer. This complete system is extremely compact, easy to use, and ensures accurate measurements on solid fuel, oil, and gas systems.

Advantages of the testo 380 fine particle measuring system

  • Suitability permit received for fuels 1-8, levels 1 and 2
  • Measurement system comprising of testo 380 fine particle measuring instrument and testo 330-2G LL combustion analyzer
  • The testo 380 fine particle measuring instrument allows you to carry out effortless and straightforward measurements directly on site
  • testo 330-2G LL combustion analyzer: System control center and combustion analyzer
  • Parallel measurement of particle matter, O2, and CO in real time
  • Charts used to show all required measuring values for an optimum overview
  • Particularly cost effective operation and maintenance
  • Effortless handling and easy transportation
  • Fully TÜV-tested for limit value levels 1 and 2 and in accordance with VDI 4206 Sheet 2
  • High tech in a portable case: Measurement of all relevant values with just one probe

General technical data

Weight
279 oz. / 7900 g
Measuring range
0 to 300 mg/m³
Accuracy
acc. VDI 4206-2
Resolution
0.1 mg/m³ (>5mg/m³)
Dimensions
19 x 14 x 7 in. / 475 x 360 x 190 mm
Operating temperature
41° to 104 °F / +5 to +40 °C
Housing
ABS
Protection class
IP40
Display type
LCD
Display function
shows warm-up phase and operational readiness
Power supply
via internal mains unit: 100 V AC/0.45 A to 240 V AC/0.2 A (50 to 60 Hz)
Maximum
500.000 readings
Storage temperature
-4° to 122 °F / -20 to +50 °C
testo 380 fine particle measurement instrument with particulate matter probe and cleaning set, testo 330-2G LL combustion analyzer with mains unit (incl. Bluetooth, H2-compensated CO cell), modular flue gas probe (length 300 mm, Ø 8 mm), and combustion air temperature probe (length 190 mm)

  • Instruction manual EasyHeat software(3.55 MB)
  • Testo ZIV driver ZIV 2000 for testo 320 and testo 330(v2.1, 2.22 MB)
    Testo ZIV driver in the 2000 version. The Testo ZIV driver is used to connect the testo 320 and testo 330 measuring instruments to an application program (sweeping district administration program) according to the interface Version 2.0 defined by the Zentralverband des Schornsteinfegerhandwerks (Central Association of Chimney Sweeps, ZIV). Please check with the manufacturer of your application program as to whether this interface is supported. If Microsoft .NET Framework 4.0 has not been installed on the computer, it must be downloaded from the Microsoft website and installed on the system.
  • Testo ZIV driver for testo 300, testo 320 and testo 330(v2.3, 64.11 MB)
    The Testo ZIV driver is used to connect the testo 300, testo 320 and testo 330 measuring instruments to an application program (sweeping district administration program) according to the interface defined by the Zentralverband des Schornsteinfegerhandwerks (ZIV, Central Association of Chimney Sweeps) in version 1.0 of 01. August 2012, in version 2.0 of 13. February 2017 as well as version 3.0 from 02. July 2021. Please check with the manufacturer of your application program as to whether this interface is supported.
  • testo 380 Box(V1.17, 1.75 MB)
  • Firmware Update testo 380(63.98 MB)

Accessories

Connection cable

: 0449 0047

USB Connection - (USB A to USB Mini B)

 USB connection cable, instrument to PC - (USB A to mni B) 

$ 53.00
testo-Schnelldrucker IRDA mit kabelloser Infrarot-Schnittstelle

: 0554 0549

testo IR Printer - IrDA printer

Documentation of readings in black and white

$ 476.00
Spare thermal paper

: 0554 0568

Spare thermal paper

Spare thermal paper, permanent ink

$ 40.80
Ausleseadaper für Feuerungsautomaten testo 330-1/-2 LL

: 0554 1206

Readout adapter for automatic furnaces

Readout adapter for automatic furnaces

PC Software testo EasyHeat

: 0554 3332

testo EasyHeat v2.12 SP7 - PC software (interface cable not included)

Set up, download and analyze data - unique data streaming mode

$ 187.00
Spare dirt filters

: 0554 3381

Spare particle filter, pack of 20 - Spare particle filter, pack of 20

For use with the testo 350 Portable Emissions Analyzer

$ 155.00
Headquarters
Testo Inc.
40 White Lake Road
07871Sparta
New Jersey
800-227-0729

© 2026